Zig Rotator for Snow Machines - $2600.00
Motorized Rotating Mount. Rotates one snow Machine product between two programmable show positions: max rotation 180 degrees. 250lb. capacity. Contact Closure and DMX remote port. Five Speeds available via DMX plus travel direction. Includes Snow Machine mount and truss attachment via dual C-Clamps. 110V or 220V. Designed to increase the disbursement of snow generated by a single snow machine. It will increase the spray pattern from one machine to three machines. It’s rotating angle is 180 degrees of oscillation. This oscillating unit has the capacity of 250 pounds of hanging weight. This unit can be used with any of our snow machines. The Zig Rotator can be controlled by DMX or contact closure.
Available in 110V or 220V.

Rent this item for $375 per day.

Buy or Rent

Can be used with the following:

• T-1000
• T-1100
• T-1500
• T-1600
• Bubble Masters
• T-5000
• Holey Smokes
• Cryo Jet
• X-Stream

Auto Refill Pumping Station - $895.00
Fluid refill pumping system that automatically maintains fluid levels in your special effects devices. Specially designed for Snowmasters snow machines but is compatible with all other equipment that utilizes liquids. It can be used in machines such as foggers or hazers.
The system detects the fluid level in the equipments small built in reservoir and signals a transfer pump connected to a multi-supply drum to refill the reservoir, all without user intervention. This is an ideal solution for installations with limited or difficult access such as ceilings or stages.

Not warrantied under regular snowmasters warranty program, but under “30 Day Limited Warranty”.

Downloads
• Specifications Sheet
• Installation Diagram
• Manual

Snow Machine Hard Wire Remote
$125.00

The snow machine hardwire remote™ is a design specifically to control all SnowMasters snow machines. Uses as a remote control source to operate snow machines on the 900 mode. Remote includes a 25 foot five pin DMX male quick connect. The remote cable can be extended by adding longer length five pin DMX cable. This remote actually is a two channel DMX simulated controller. It can be used on any two channel devise. When used in any snow machine it can be daisy chained to as many machines as necessary.

Buy or Rent?

Standtek 3000 - $ 475.00
Supports up to 132 Pounds with a Maximum Height of 9' 8".

The StandTek 3000 is the first stand in the new line of the Mobil Tech International series combining innovative new features with proven Mobil Tech quality. In its original design as the SP1TA, this stand has been sold world-wide for years and is known as having a superior value for a light-weight tri-pod stand. With its recent design improvements and transformation into the new StandTek 3000, it now offers even more value and performance at a competitive price.

Manufactured from steel plus an aluminum mast, the StandTek 3000 can support up to 132 pounds with a maximum height of 9' 8". Its strong metal base with protective rubber feet easily slides up-and-down the center pole for effortless installation. Take a look at the brochure on the lower part of this page to see all the new components that have been added to improve this already good stand.

The StandTek 3000 is the perfect stand for any application where a lot of weight and height is not an issue. It can be used separately with a TBar to hang up to 6 lights or in a bridging combination with another stand to span some truss and hang lights or speakers. If you have a room with 10 to 12 foot ceilings, this stand will give you all the height you need. Don't compare this stand with any of the low-priced imports because it is in a class of its own with its standard features. The StandTek 3000 has a 35 mm shaft on top and uses the following accessories.

All Mobil Tech stands and accessories have a 1 year warranty against defects in materials and workmanship. They are manufactured to the toughest German TUV standards and every stand has been tested and certified by qualified engineers. Engineering documentation is available on all Mobil Tech products.

ACCESSORIES: (View Accessories page)

• T-Adaptor 250/300: Adjustable Truss Adaptor with 35 mm Shaft. Adjusts from 8" to 12".
• TBar 3: 5' TBar with a 2" Pipe for Lights and a 35 mm Shaft.

Downloads
• StandTek 3000 Manual
• StandTek 3000 Specifications

Trussing For Mobil Tech Stands - $ 205.00 per section
Each Section = 12 inch X 5 feet Truss

Quik Stage offers three separate choices of aluminum trussing designed to work perfectly with any one of the Mobil Tech stands and truss adaptors. We offer Duo, commonly known as Ladder Truss, Trio, commonly know as Tri Truss and Quatro, commonly know as Box Truss.

Each of our truss designs come standard with a quick-connect system designed to make assembly quick and easy saving you valuable labor time. The following drawings will show you exactly how easy it is to assemble. Manufactured by Milos Structural Systems and carries a life time warranty against defects in materials and workmanship under normal use.

Following the drawings is a detailing listing of each size truss we offer along with lengths and weights of each size truss. We also offer custom trussing including circle trusses and probably any other corner or connection you can imagine. Better yet, they are all considered standard and most likely are in stock ready for immediate shipment.

ACCESSORIES: (View Accessories page)

• T-Adaptor 250/300: Adjustable Truss Adaptor with 35 mm Shaft. Adjusts from 8" to 12".
• TBar 3: 5' TBar with a 2" Pipe for Lights and a 35 mm Shaft.

Buy

DMX Mini control board - $ 399.00

The Pocket Console™ is the inexpensive source for the smallest, most graphic "hands-on" and "user-friendly"DMX-512 theatrical lighting console made.

• It is small, lightweight, portable and designed to be hand held
• Levels are set using eight faders (slider pots)
• Each FADER has an associated bump button
• 512 dimmer addresses are patchable to any of the eight faders
• The faders are patchable using from 0 to 512 dimmer addresses per fader
• The unit is powered by a 9v battery OR by a 120v AC power supply
  
  

Downloads
• DMX Mini Control Board Manual

CO2 Blast/Confetti Master Control Box - $250.00
Designed to make controlling "instant-on" effects easy. Provides momentary output to any of three devices attached to the output. Input is a single 110 volt supply. Three momentary switches allow momentarily activation of the corresponding output power plug. Each output is held "on" for as long as the button is pressed. Each switch can handle up to 15 amps with a maximum combined load of 20 amps at 110 volts.  Ideally suited for equipment such as CO2 devices, confetti, lighting and other special effects equipment requiring short or quick activation. Eliminates the need for expensive control equipment or DMX controllers. Ten foot power cord included. 

(GFI protection recommended for wet/outdoor applications and available separately.)

Click here to Buy

Snow Curtain Controller - $ 85.00
Exclusively designed for the Snow Curtain. This devise permits the control of snowfall on the snow curtain. From a gentle fall to heaver snow fall. Great for non theatrical application such as window displays were a theatrical light board is not used.

Click here to Buy

DMX CBI Heavy black flexible Duty DMX Wire
25 feet $49.00
50 feet $ 79.00
Neutrik X-Series 5 Pin Nickel XLR's - compression strain relief.
Available in 3 pin and shorter or longer lengths..

Click here to Buy 25 feet

Click here to Buy 50 feet

W-100 Wireless remote - $125.00
Used for any of our snow machines, controls power on and off only. Up to 100 feet and up to 4 different frequencies available. Comes with key chain"On-Off" remote controller.

Rent this item for $25

Buy or Rent?

The Amazing Snowman Replacement Wireless Remote - $20.00
This item can only be used with the retail snowman. Includes batteries.

Buy

DMX Controller Module - $125 to $500
For all snow machines. Line voltage relay pack plugs directly into the power input of the snow machines.

Rent this item for $50

Buy or Rent?

Downloads
• Installation Instructions

T-1100 Weather Resistant Covers - $125
Make your T-1100 outside rated for rain or shine. Easy to install and still have access to the controls and gallon reservoir. Made out of all weather vinyl. Available in any color. Standard in black.

Downloads
• Installation Instructions

T-1500 Weather Cover - $95.00

Designed for those that want to leave their T-1500 outside. Easy installation. Protects the electronics without reducing the performance. Access to the control is still available with a velcro access panel. Available in any color. Standard in black.

Downloads
• Installation Instructions

T-1600 Weather Cover - $125.00

Theme park designed for the extended outdoor theaters. Easy to install. Now you can leave your machine in the rain without worry of damaging the machine.
Easy access to the one gallon reservoir and the controls. Available in any color. Standard in black.

Downloads
• Installation Instructions

Pale Mounting Bracket - $185
Engineering Rated at 5 gallons. Used for suspending fluid reserve alongside snow machines.

Rent this item for $20

Buy or Rent

Timer-Multi Relay - $995
Infinitely programmable timer. Heavy duty enclosure. Custom made for each use can control up to 4 snow machines per controller. Designed for large malls or theme parks. Dates and times are programmed by laptop.

Downloads
• Instructions

Timer-Single Relay - $550.00
Timer can be set for on and off feature and still have repeat cycle time also. This timer is design to perform timed functions on and off in a 24 hour day. Typically these timers are called repeat cycle timers. This devise is broken up into two parts. A clock and a cycling repeat timer. These timers are designed to cycle a devise on and off during a user defined period. In that period the user has the option of being on and off as many times as they like.

Downloads
• Instructions

• Buy T-1100 - $400.00
• Buy T-1500 - $900.00
• Buy T-1500 Mini - $800.00
• Buy T-1600 $ 745.00

SpTek 4000 - $775.00
Supports up to 176 Pounds with a Maximum Height of 13' 5".

Of all the Mobil Tech stands available in its wide range of stands, the SpTek 4000 is one of the most popular stands we offer. Its maximum height of 13' 6" and weight support up to 176 pounds, makes this the perfect stand for any mid-range lighting or sound application.

Manufactured from steel, this stand is tough enough to handle any mid-range application but light enough to transport with ease by one person. It features double-locking on each mast for extra security and comes standard with a heavy-duty winch with safety friction brake. Additionally, it offers 3 separate foot print positions along with one of the legs that can be extended for uneven terrain or for use on a step. Black epoxy painted legs and a chromed mast help keep this stand looking great and its low loading height add to its already long list of standard features.

If you are looking for a high performance tri-pod stand with standard features unmatched by any other manufacturer, you have to consider the SpTek 4000. Its competitive purchase price easily makes it the best valued stand in its class. The SpTek 4000 has a 35 mm shaft on top and uses the following accessories.

All Mobil Tech stands and accessories come with a one year warranty against defects in materials and workmanship. They are manufactured to the toughest German TUV standards and every item has been tested and certified by qualified engineers. Engineering documentation is available on all Mobil Tech products.

ACCESSORIES: (View Accessories page)

• T-Adaptor 250/300: Adjustable Truss Adaptor with 35 mm Shaft. Adjusts from 8" to 12".
• TBar 3: 5' TBar with a 2" Pipe for Lights and a 35 mm Shaft.

Downloads
• StandTek 4000 Specifications